Carolina NeuLog Salinity Manuel d'utilisateur télécharger pdf

NEULOG SALINITY SENSOR GUIDE

NeuLog salinity sensor

NUL-228 Carolina # 369657

The NeuLog salinity sensor can be used for any science experiment or activity which

utilizes solutions that have a saline (salt) component such as in the fields of

Chemistry, Biology, Earth Science, Environmental Science, Biochemistry, Physics,

etc.

The sensor comes pre-calibrated so you can start experimentation right out of the box

using any of the following guides.

Just a few of the thousands of possible experiments that can be done with the NUL-

228 sensors are: Monitoring of ecological systems, chemical analysis and

identification, environmental health testing, water quality testing, chemical properties,

properties of electricity, etc.

The NeuLog salinity sensor can use any of the following units of measure:

 Percentages (%): The total saline percentage out of the whole sample.

 Parts per million (ppm): The number of salt molecules per million molecules.

 Milligrams per liter (mg/L): The total mass of dissolved salts per liter of

volume.

Probe usage and care:

The probe has two flat electrodes with known surface areas and distance between

them. A signal is supplied to the electrodes and by testing the signal behavior, the

salinity of the solution is calculated.

General care:

 Avoid touching the probes flat green surface if possible.

 Never submerge the probe’s or sensor’s plastic body in any liquid.

 Gently rinse the electrodes off with distilled water after each use and

between samples to avoid damage and contamination.

 Handle and store with care to avoid damaging or chipping the electrodes.

Quick start procedure:

PC or Mac Computer

Materials needed:

 NUL-228 Salinity Sensor

 USB-200 USB Module

 A USB to mini USB cable (which comes with the USB-200)

Your salinity sensor needs to be connected to a USB-200 module. The USB-200

module then connects to a computer via a USB to mini-USB cable. Please note that

you cannot plug the salinity sensor directly into the computer.

Resident PC software and browser based software can be downloaded for free at

www.NeuLog.com/dowload as well as a full software user guide. Note: Make sure not

to download and install both types of software, they will conflict on the computer.

Procedure:

1. Install the NeuLog software

2. Connect the USB-200 module to the PC or Mac

3. Connect the salinity sensor to the USB-200 module (they directly plug

together). Please note there is no calibration required for this sensor.

4. Open the NeuLog software.

5. Once a salinity sensor logo appears on the left side of the screen the probe

has been automatically identified and you can begin experimentation.

6. If the salinity sensor is not automatically identified, click on the “Search for

sensors” icon to find the sensor.

7. Select the “On-line experiment” button; this will open a graph below.

8. Click on the “Module setup” button located on the salinity sensor icon in the

module window to change the sensor settings if need be.

9. Click on the experiment set up button to change the experiment settings if

need be (experiment duration for example).

10. The salinity sensor will give a live reading in the box to the left of the screen

while plugged in.

11. To run an experiment and collect data click “Run experiment”.

12. To end data collection early, click “Stop experiment”.

1 2 3 4

Résumé du contenu

Page 1 - NeuLog salinity sensor

NEULOG SALINITY SENSOR GUIDE NeuLog salinity sensor NUL-228 Carolina # 369657 The NeuLog salinity sensor can be used for any science experiment o

Page 2 - NEULOG SALINITY SENSOR GUIDE

NEULOG SALINITY SENSOR GUIDE Tablet, smart phone device Materials needed:  NUL-228 Salinity Sensor  WIFI-201 WIFI module  BAT-200 Battery Y

Page 3

NEULOG SALINITY SENSOR GUIDE Procedure: 1. Connect the salinity sensor directly to the left side of a charged BAT-200 module. 2. When ready to co

Page 4

NEULOG SALINITY SENSOR GUIDE On the salinity probe there are two electrodes of known surface area with a known distance between them which allows fo

Commentaires sur ces manuels

Pas de commentaire

Carolina NeuLog Salinity Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Carolina NeuLog Salinity. Carolina NeuLog Salinity User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Carolina NeuLog Salinity